Forum Replies Created
-
AuthorPosts
-
September 23, 2020 at 1:04 am in reply to: Notifications feature has HUGE impact! #6426 Report Abuseanthonyd73111Member
<p style=”text-align: center;”>The previous post was for sell pump only, for the septic its exceeds 1.5kw for 3secs, and exceeds 1.2 kw for 10secs, and finally exceeds .5kw for 5mins or however many mins that would reveal pump is stuck on. You can call me on Weds after 10am est. Goodluck, Anthony</p>
September 23, 2020 at 12:44 am in reply to: Notifications feature has HUGE impact! #6423 Report Abuseanthonyd73111MemberOk set running watts if exceeds 2.0 kw for 10 secs, set another for if exceeds 2.9kw for 3 secs, then this is up to you,set if exceeds 1.0kws for the minutes not to exceed like 5 mins, this last one will notify if pump not shutting off because it seems like it stays on about 1-2 mins so if on longer then say 5 mins it will tell you. If you get false notifications just raise kws by .1 up at a time. These 3 will tell you a host of early problems, once set propdr you shouldnt get any notifications. Tweaking will be necessary depending on water depth and other factors. Just call me 7274693401 if need to talk in detail. Goodluck, Anthony
- This reply was modified 4 years, 2 months ago by anthonyd73111.
- This reply was modified 4 years, 2 months ago by anthonyd73111.
September 21, 2020 at 11:50 pm in reply to: Notifications feature has HUGE impact! #6415 Report Abuseanthonyd73111MemberRemember sec data only goes back 3 hrs. (I dont like) so several captures may be necessary. The sec data will show start watts, for RLA setting , then a running watts setting and 3rd a running too long past time setting. Without knowing the sequence of operation of your septic this is a place to start, with tweaking later.
September 21, 2020 at 11:25 pm in reply to: Notifications feature has HUGE impact! #6414 Report Abuseanthonyd73111MemberSend me 1sec data with motor starting up several times and running for several minutes, I can the give you setting for notifications, the 1 min data wont work for that.
September 21, 2020 at 11:22 pm in reply to: Notifications feature has HUGE impact! #6413 Report Abuseanthonyd73111Member<p style=”text-align: center;”>To set notification for past runtime just choose a low running wattage below normal run watts could be 5,10,20watts for a period of time say 1hr, then you will get notified. This is easy compared to a bad motor from too high startup watts which would be set to just above start watts for say2 secs. Another could be for too high running watts, set just above normal running watts for say 5 secs, some tweaking for falses may be required. My setting have been working well with several motors, compressors.</p>
September 21, 2020 at 11:21 pm in reply to: Notifications feature has HUGE impact! #6412 Report Abuseanthonyd73111MemberTo set notification for past runtime just choose a low running wattage below normal run watts could be 5,10,20watts for a period of time say 1hr, then you will get notified. This is easy compared to a bad motor from too high startup watts which would be set to just above start watts for say2 secs. Another could be for too high running watts, set just above normal running watts for say 5 secs, some tweaking for falses may be required. My setting have been working well with several motors, compressors.
anthonyd73111MemberGood point, it always gets better (except for removing data below 35 watts) waiting for Gen2, my guess is it will be fantastic.
-
AuthorPosts