Emporia Community

Community Forum for Emporia

Forum Replies Created

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • in reply to: Something wrong with api.emporiaenergy.com? #10076 Report Abuse
    lasersbee
    Member

    Back to normal here (Canada) as well.Thanks for the Fix. Would like to

    Know what caused the App to go down.

    in reply to: Something wrong with api.emporiaenergy.com? #10023 Report Abuse
    lasersbee
    Member

    Completely agree…There should be an Emporia Software solution for local in Home/Shop

    monitoring without the need for the ‘CLOUD’

    in reply to: Something wrong with api.emporiaenergy.com? #10018 Report Abuse
    lasersbee
    Member

    Yeah… Got the same Zero Data this morning as well…

    seems like the Cloud Info Support is Down.

    Not a good sign IMO

     

    Jerry

    lasersbee
    Member

    Don’t hold your breath on a New Firmware update. I have a Daylight Saving Time

    problem that is in the WEB PC App which BTW works fine on the Cell Phone APP.

    No one seems to be interested in looking into the WEB App for an obvious Bug.

    Should have gone another route.

     

    lasersbee

    in reply to: Main Panel External Install in Plastic Box OK? #9448 Report Abuse
    lasersbee
    Member

    That’s the way I do it for both my Emporia Vue 2 systems.

    No room in the Panels.

    lasersbee

    in reply to: High balance even when all circuits monitored #9447 Report Abuse
    lasersbee
    Member

    This is how it seems to work…. The Main Line CTs read a value (X). The

    single circuit CT readings are added up (CT1+CT2+CT3… etc)=(Y). Then

    the EMP takes X and Y and finds the delta (difference + or -) and shows

    that on the Balance line.

    Had the same problem with about 50-60 Watts Balance showing. This only

    seemed to happen when one or both of my shop heaters turned on.

    I went into manage circuits and dropped my 2 heater voltages to read

    1.98 instead of 2.00. This solved my problem.

     

    lasersbee

    lasersbee
    Member

    You can get Male and Female and Shielded wire from DigiKey.

    You can then build your own cables to any length.

    Another solution would be looking at AliExpress.

     

    lasersbee

    in reply to: Introduce Yourself! #9444 Report Abuse
    lasersbee
    Member

    You can put as many different circuits through a CT as will fit of the same Voltage 120VAC 240VAC

    It will show the total readings of all those circuits but not idividually.

     

    lasersbee

    in reply to: Introduce Yourself! #9432 Report Abuse
    lasersbee
    Member

    Similar problem here… Old Farm house with Packed Panels.

    I decided to install the Current Clamps in the Panels and run the

    Clamp wires outside the panel where I also installed the Emporia

    Control box.

     

    lasersbee

    in reply to: Introduce Yourself! #9431 Report Abuse
    lasersbee
    Member

    With all those circuits it may be cheaper to get another 16 Ch Emporia system…

     

    lasersbee

    in reply to: Introduce Yourself! #9430 Report Abuse
    lasersbee
    Member

    Hi,

    new guy on the bock just saying Hi… Just registered. I’m in Quebec Canada and

    have two Emporia systems…. One 16 Channel for the home and an 8 Channel for the

    Shop. I bought these systems to get a long term base measurement of present Energy

    usage before installing some 24K BTU Heat Pumps and an on demand 18KWH water

    heater.

    So far I’m quite happy with my EMP systems being able to see my Energy usage

    on my Phone and my computers.

     

    lasersbee

    in reply to: No Usage detected for Heat Pump Water Heater #9429 Report Abuse
    lasersbee
    Member

    I have a similar problem but with all 8 circuits…. It seems that my problem is due to

    the time registered. After clicking on a Circuit (in Seconds) and the page goes to the

    Graph page… Look at the top right of the screen to see the present time. We just did

    a Daylight saving time and my time shows 1 hour later than real time. That posted

    time will not arrive for another hour. Scrolling backwards in time on that page will

    get you to the real time and you can see some data…. BUT it will not actual time

    increment. There is a bug in the PC App. My Phone App works correctly.

     

    lasersbee

Viewing 12 posts - 1 through 12 (of 12 total)