Forum Replies Created
-
AuthorPosts
-
January 16, 2024 at 10:06 pm in reply to: Can I put multiple CTs on one circuit? #10269 Report AbuseyyzguyMember
That seems reasonable to me, as long as you don’t ALSO put a CT on the combined conductor.
January 14, 2024 at 11:15 pm in reply to: Is there a way to see Energy Consumption for Last Month/Year for 4PM-9PM? #10253 Report AbuseyyzguyMemberYou can export raw data in CSV format. I haven’t done it myself, but there’s probably enough information to accomplish what you’re looking for
yyzguyMemberYeah, the scale change when scrolling is annoying. I think others (maybe myself even) have asked about that in the past. Seems there’s been very little activity from the devs in quite some time.
How about putting that third compressor on its own CT and leave your smallest loads unmonitored? Shortly after installing my own system, I quickly figured out which circuits use the least amount of energy and left those unmonitored. My balance never exceeds 5%.
- This reply was modified 1 year, 4 months ago by yyzguy.
June 30, 2023 at 1:46 pm in reply to: Can I monitor mains power by summing circuits? #9649 Report AbuseyyzguyMemberI’m pretty sure you’ll need to use option 1. Emporia has suggested they intend to introduce “nested vues” in the future but haven’t done so.
You shouldn’t have any problems using the flexible CT clamps. My busbars look similar to yours and fit easily. However, unless you can turn off the power from the meter, please don’t install them above the breaker….those are hot! Install them below the breaker, with the breaker in the off position.
- This reply was modified 1 year, 4 months ago by yyzguy.
May 15, 2023 at 7:06 pm in reply to: Any way to disable switching in smart plugs? #9559 Report AbuseyyzguyMemberI have smartplugs on a freezer and a refrigerator and haven’t had any issues after two power outages
yyzguyMemberIs it possible the CT accidentally became unplugged from the Vue?
November 17, 2022 at 2:54 am in reply to: Can’t reset Wifi on Vue Utility Connect #9103 Report AbuseyyzguyMemberFor the benefit of others, please post back here after you find out more from support.
November 16, 2022 at 9:58 am in reply to: Can’t reset Wifi on Vue Utility Connect #9096 Report AbuseyyzguyMemberSeemed like it was worth trying. At this point, you should probably contact support. They don’t seem to check the community forums very often. Perhaps the device is defective.
November 16, 2022 at 4:20 am in reply to: Can’t reset Wifi on Vue Utility Connect #9094 Report AbuseyyzguyMemberMight there be an unsecured WiFi access point nearby that it’s connecting to before you have a chance to reconfigure it ? If so, you’d probably be able to see it using any other WiFi client device.
November 15, 2022 at 9:44 pm in reply to: Can the Gen2 Vue be installed on a breaker larger than 15A? #9092 Report AbuseyyzguyMemberIs their a way to sync the inverter to the grid so they are locked into the same phase?
November 13, 2022 at 8:43 pm in reply to: Not sure to go about putting clamps on mains #9083 Report AbuseyyzguyMemberAre you sure those are Mains? What country are you located? Can you provide a picture showing the entire panel including the meter.
November 7, 2022 at 6:23 pm in reply to: Using Emporia Vue Gen2 With Starlink (UK) #9057 Report AbuseyyzguyMemberI have iPhone and didn’t have this issue
November 6, 2022 at 4:33 pm in reply to: Using Emporia Vue Gen2 With Starlink (UK) #9052 Report AbuseyyzguyMemberWhen I was installing mine, they actually did answer on a weekend. It was a simple question and the person might have been working from home. As far as your question, mine is mounted in a difficult to reach location so, I’m not able to compare, sorry
November 1, 2022 at 3:16 pm in reply to: Using Emporia Vue Gen2 With Starlink (UK) #9039 Report AbuseyyzguyMemberSounds more like a Bluetooth problem rather than internet problem. For Bluetooth it’s important to be reasonably near the Vue. Bluetooth is a direct connection between two devices. I’d suggest getting as close as possible to the vue.
Also, verify the vue has power and the phone has Bluetooth enabled. Cycle the power on vue if necessary
November 1, 2022 at 12:59 am in reply to: Using Emporia Vue Gen2 With Starlink (UK) #9033 Report Abuse -
AuthorPosts